Google Search

Custom Search

Tuesday, July 22, 2008

Turning


A. Definition

1. A method for removing the surface from a circular piece by bringing the cutting edge of a tool against it while the piece is rotated.

2. Turning is the machining operation that produces cylindrical parts. In its basic form, it can be defined as the machining of an external surface:
  • with the workpiece rotating,
  • with a single-point cutting tool, and
  • with the cutting tool feeding parallel to the axis of the workpiece and at a distance that will remove the outer surface of the work.
B. Cutting Factors in Turning

1.
Speed
Always refers to the spindle and the workpiece. When it is stated in revolutions per minute(rpm) it tells their rotating speed. But the important figure for a particular turning operation is the surface speed, or the speed at which the workpeece material is moving past the cutting tool. It is simply the product of the rotating speed times the circumference (in feet) of the workpiece before the cut is started. It is expressed in surface feet per minute (sfpm), and it refers only to the workpiece. Every different diameter on a workpiece will have a different cutting speed, even though the rotating speed remains the same.

2.Feed
Always refers to the cutting tool, and it is the rate at which the tool advances along its cutting path. On most power-fed lathes, the feed rate is directly related to the spindle speed and is expressed in inches (of tool advance) per revolution ( of the spindle), or ipr. The figure, by the way, is usually much less than an inch and is shown as decimal amount.

3.Depth of Cut
It is practically self explanatory. It is the thickness of the layer being removed from the workpiece or the distance from the uncut surface of the work to the cut surface, expressed in inches. It is important to note, though, that the diameter of the workpiece is reduced by two times the depth of cut because this layer is being removed from both sides of the work.

C. Turning Process

1. Facing Cut

It involves moving the cutting tool across the face (or end) of the workpiece and is performed by the operation of the cross-slide, if one is fitted, as distinct from the longitudinal feed (turning). It is frequently the first operation performed in the production of the workpiece, and often the last- hence the phrase "ending up".

2. Roughing Cut

An initial pass of the cutting tool that emphasizes heavy metal removal rates, high feed rates, and a heavy depth of cut.



3. Finishing Cut


A final pass of the cutting tool that emphasizes dimension accuracy, surface finish, higher speeds and light depth of cut.




D. Turning Machines

1. Turret Lathes

In a turret lathe, a longitudinally feedable, hexagon turret replaces the tailstock. The turret, on which six tools can be mounted, can be rotated about a vertical axis to bring each tool into operating position, and the entire unit can be moved longitudinally, either annually or by power, to provide feed for the tools. When the turret assembly is backed away from the spindle by means of a capstan wheel, the turret indexes automatically at the end of its movement thus bringing each of the six tools into operating position. The square turret on the cross slide can be rotated manually about a vertical axis to bring each of the four tools into operating position. On most machines, the turret can be moved transversely, either manually or by power, by means of the cross slide, and longitudinally through power or manual operation of the carriage. In most cased, a fixed tool holder also is added to the back end of the cross slide; this often carries a parting tool.

2. Single Spindle Automatic Screw Machines

There are two common types of single-spindle screw machines, One, an American development and commonly called the turret type (Brown & Sharp), is shown in the following figure. The other is of Swiss origin and is referred to as the swiss type. The Brown & Sharp screw machine is essentially a small automatic turret lathe, designed for bar stock, with the main turret mounted on the cross slide. All motions of the turret, cross slide, spindle, chuck, and stock-feed mechanism are controlled by cams. The turret cam is essentially a program that defines the movement of the turret during a cycle. These machines usually are equipped with an automatic rod feeding magazine that feeds a new length of bar stock into the collect as soon as one rod is completely used.

3. CNC Machines

Nowadays, more and more Computer Numerical Controlled (CNC) machines are being used in every kinds of manufacturing processes. In a CNC machine, functions like program storage, tool offset and tool compensation, program-editing capability, various degree of computation, and the ability to send and receive data from a variety of sources, including remote locations can be easily realized through on board computer. The computer can store multiple-part programs, recalling them as needed for different parts.

E. Turning Tools
1.

HSS Lathe Turning Tools

2.

Turning Tool Holder

3.


Self Centering Lathe Chucks - 3Jaw

4.

Independent Lathe Chucks - 4 Jaw

5. Lathe Chuck Keys

6. Revolving Center / Live Center

7. Center Drill

8. Lathe Dogs















No comments: